Cereals and cereal products - Determination of moisture content (Routine method)
1. SCOPE AND FIELD OF APPLICATION
This International Standard specifies a routine method for the determination of the moisture content of cereals and cereal products,
The method is not applicable to maize, for which a method is specified in ISO 6540, Maize - Determination of water content (on milled grains and on whole grains).2
2. REFERENCES
ISO 711, Cereals and cereal products Determination of moisture content (Basic reference method)
ISO 950, Cereals - Sampling (as grain).
3. DEFINITION
Moisture content: The loss in mass, expressed as a percentage, undergone by the product under the conditions specified in this International Standard.
4. PRINCIPLE
Following any grinding and conditioning, drying of a test portion at a temperature between 130 and 133°C, under conditions which enable a result to be obtained which is in agreement with that obtained by the basic reference method (see ISO 711).
5. APPARATUS
5.1 Analytical balance.
5.2 Grinding mill, having the following characteristics: characteristics:
5.3 Metal dish, non-corrodible under the test conditions, or, failing this, a glass dish, with a sufficiently tightfitting lid, and having an effective surface area enabling the test portion to be distributed so as to give a mass per unit area of not more than 0.3 g/cm².
5.4 Constant-temperature oven, electrically heated, controlled in such a way that, during normal working, the temperature of the air and of the shelves carrying the test portions is within the range 130 to 133°C in the neighbourhood of the test portions.
The oven shall have a heat capacity such that, when initially adjusted to a temperature of 131°C, it can regain this temperature in less than 45 min (preferably in less than 30 min) after insertion of the maximum number of test portions that can be dried simultaneously.
The effectiveness of the ventilation shall be determined using durum wheat semolina, of maximum particle size 1 mm, as the test material. The ventilation shall be such that after insertion of the maximum number of test portions that the oven will accommodate, and drying at a temperature of 130 to 133°C, the results, after heating the same test portions for 2 hand then for a further 1 h, do not differ by more than 0, 15 g of moisture per 100 9 of sample.
5.5 Desiccator, containing an effective desiccant.
6. SAMPLING
See ISO 950.
7. PROCEDURE
7.1 Preparation of the test sample
7.1.1 Products not requiring to be ground
Products having no particles greater than 1.7 mm, less than 10% (m/m) being over 1 mm and more than 50 % (m/m) being less than 0.5 mm, do not need to be ground before the determination.
Well mix the laboratory sample before taking the test portion (7.2.1)
7.1.2 Products requiring to be ground
If the sample does not have the particle size characteristics mentioned in 7.1.1, it shall be ground either without preconditioning (7.1.2.1) or with preconditioning (7.1.2.2)
7.1.2.1 Grinding without pre-conditioning
For products which are not likely to undergo variations in moisture content in the course of grinding [in general, products with a moisture content between 7 and 17 % (m/m), (see 9.1)] carry out grinding without pre-conditioning.
Adjust the grinding mill (5.2) to obtain particles of the dimensions indicated in 7.1.1, grind a small quantity of the laboratory sample and discard this quantity.
Then quickly grind a quantity of the laboratory sample slightly greater than that required for the test portion (about 5 9), and immediately proceed in accordance with 7.2.2.
7.1.2.2 Grinding with pre-conditioning
Products which are likely to undergo changes in moisture content during the course of grinding in general, products with a moisture content more than 17 % (m/m)' or less than 7 % (m/m)] shall be preconditioned so as to bring their moisture content to between 7 and 17 % (m/m)' [preferably between 9 and 15% (m/m) (see 9.1)], before grinding.
If the moisture content is more than 17 % (m/m)', the more frequent case, weigh to the nearest 1 mg a sufficient quantity of the laboratory sample to provide a test portion slightly greater than 5 9 (see 7.2.2) and carry out a pre-drying operation according to the instructions in 7.3, except that the time of heating in the oven (5.4) shall be 7 to 10 min and the cooling of the product to laboratory temperature shall be carried out with the dish (5.3) uncovered and without a desiccator, for at least 2 furs.
In the case of products having moisture contents of less than 7 % (m/m), weigh to the nearest 1 mg, a sufficient quantity of the laboratory sample to provide a test portion slightly greater than 5 g (see 7.2.2), place it in a suitable atmosphere (generally that of the laboratory) and leave it until a moisture content within the limits indicated above is obtained.
Weigh the sample to the nearest 1 mg, immediately grind it, controlling the grinding so as to obtain particles of the dimensions indicated in 7.1.1, and immediately proceed in accordance with 7.2.2.
7.2 Test portion
7.2.1 For products not requiring to be ground, rapidly weigh, to the nearest 1 mg, a quantity slightly greater than 5 9 of the test sample (7.1.1) in the dish (5.3), previously dried and tared, together with its. lid, to the nearest 1 mg.
7.2.2 In the case of products which have had to be ground, weigh all the grindings obtained (7.1.2.1 or 7.1.2.2) to the nearest 1 mg, in the dish (5.3), previously dried and tared, together with its lid, to the nearest 1 mg.
7.3 Drying
Place the open dish containing the test portion (7.2), together with the lid, in the oven (5.4) and leave for 2 h (90 min for flours) from the moment when the oven temperature is again between 130 and 133°C.
Rapidly take the dish out of the oven, cover it and place it in the desiccator (5.5); when several tests are being carried out simultaneously, never place dishes on top of one another in the desiccator.
When the dish has cooled to laboratory temperature (generally between 30 and 45 min after it has been placed in the desiccator), weigh it to the nearest 1 mg.
7.4 Number of determinations
Carry out two determinations on test portions taken from different test samples but from the same laboratory sample.
8. EXPRESSION OF RESULTS
8.1 Method of calculation and formulae
The moisture content, expressed as a percentage by mass of the product as received, is given by the following formulae:
a) without preconditioning:
where
m0 is the mass, in grams, of the test portion (7.2.1 or 7.2.2);
m1 is the maass, in grams, of the test portion after drying (7.3)
b) with preconditioning:
where
m0 is the mass, in grams, of the test portion (7.2.1 or 7.2.2);
m1 is the mass, in grams, of the test portion after drying (7.3);
m2 is the mass, in grams, of sample taken before preconditioning (7.1.2.2);
m3 is the mass, in grams, of the preconditioned sample (7.1.2.2).
Take as the result the arithmetic mean of the determinations if the requirement concerning repeatability (see 8.2) is satisfied.
Round the result to the nearest 0.05 units.
8.2 Repeatability
The difference between the values obtained from the two determinations (see 7.4) carried out simultaneously or in rapid succession by the same analyst shall not exceed 0.15 9 of moisture per 100 9 of sample. If it does so, the determinations shall be repeated.
8.3 Remarks
The results compared with those obtained by the basic reference method (see ISO 711) generally differ by less than 0.15 9 of moisture per 100 9 of sample.
9. NOTES ON PROCEDURE
9.1 The range of moisture contents given for conditioning products before grinding corresponds approximately in the laboratory to a temperature of 20°C and a relative humidity of 40 to 70 %. It should be modified for other atmospheric conditions.
9.2 Never place moist products in an oven containing test portions at the end of drying, as this will result in partial rehydration of the latter.
10. TEST REPORT
The test report shall show the method used and the result obtained. It shall also mention all operating details not specified in this International Standard, or regarded as optional, as well as any incidents which may have influenced the result.
The report shall include all details required for the complete identification of the sample, and in particular the date on which the analysis was carried out.
Cereals and cereal products-Determination of moisture content (Routine method)
ERRATUM
Cover page
Amend the element of the title in parentheses to read:
"(Routine reference method)"
Amend the corresponding element in the French title to read:
"(Methode de reference pratique)"
Page 1
Amend the element of the title in parentheses to read:
"(Routine reference method)"
Replace the first paragraph of clause 1 by the following:
This International Standard specifies a routine reference method for the determination of the moisture content of cereals and cereal products.