Previous Page Table of Contents Next Page


2.3. Conducting a feasibility study


2.3.1. Introduction
2.3.2. Market analysis
2.3.3. Technical feasibility
2.3.4. Financial feasibility


2.3.1. Introduction

Aspiring entrepreneurs may have an idea about the type of fruit or vegetable product that they would like to make. This can come from seeing others successfully producing a food and wanting to copy them or from talking to friends and family members about products that they think they could make. However, an idea for a business is not a sufficient reason to begin production straight away, without having thought clearly about the different aspects involved in actually running the business. Too often, people invest money in a business only to find out later that there is insufficient demand for the product or that it is not the type that customers want to buy. To reduce this risk of failure and losing money, potential producers should go through the different aspects of running their business in discussions with friends and advisers before they commit funds or try to obtain a loan. This process is known as doing a feasibility study and when the results are written down, the document is known as a business plan.

Conducting a feasibility study need not be difficult or expensive, but the most important aspects should all be taken into account to ensure that potential problems are addressed. These are summarised in the Feasibility Study Checklist in Appendix III and are described in more detail in other Sections of this book. In this Section, the following questions that can be answered by a feasibility study are addressed:

· is there a demand for the produce?

(Find out the characteristics required of the product and the size and value of the market)

· who else is producing similar products?

(Determine the number and type of competitors)

· what is needed to make the product?

(Find the availability and cost of staff, equipment, services, raw materials, ingredients and packaging)

· what is the cost of producing a product?

(Calculate the capital costs of getting started and the operating costs of production)

· what is the likely profit?

(Calculate the difference between the expected income from sales to an estimated share of the market and the costs of production)

Each of these aspects should be looked at in turn. When all the information has been gathered and analysed, it should be possible to make a decision on whether the proposed investment in the business is worthwhile or whether the producer's money could be better spent doing something else. The same considerations should be taken into account when an existing entrepreneur wishes to diversify production or make a new product.

It is also important to remember that the business plan is a working document that should be used as a framework to guide the development of a business. To do this it should be regularly updated. However, it often happens that an entrepreneur pays an adviser or consultant to prepare a business plan but then does not understand the contents, or having read it once, puts it away on a shelf never to be seen again. In the following parts of this Section, the above aspects are described in a systematic way, as should be done in a feasibility study, starting with 'The Market'.

2.3.2. Market analysis


Product quality survey
Survey of market size and value
Market share and competition


Once a potential producer decides that he wishes to start a business, the first thing to do is to find out what is the likely demand for the fruit or vegetable product that he or she wishes to make, by conducting a short market survey. Although there are market research agencies that are able to do this type of work in many developing countries, it is better for producers to do it themselves (if necessary with assistance from partners or advisers) because they will then properly understand their customers' needs and how their business should operate. If an idea is found to be feasible, this knowledge will in turn give them the confidence to go ahead when problems are encountered, knowing that their product is in demand.

Although telephone or posted questionnaires are possible, in most developing countries it is better to conduct a market survey by going out into areas where the producer expects to find consumers and asking people for their views. There are two types of information that are needed:

1) information about the product and its quality and
2) information about how much people will buy, how often and for what price.

It is important to think in advance about the type of information that is needed and to ask people the same questions each time, so that their answers can be compared and summarised. This should be a short exercise to keep the costs low and in-depth market research is not necessary for most products. A convenient way of doing this is to prepare simple questionnaires such as those shown below, which can be used by entrepreneurs to remind themselves of which questions to ask.

Product quality survey

Consumers are familiar with the types of fruit or vegetable products that are already on sale and surveys on these products are therefore easier than those for a completely new food. Questions can focus on what are the things that consumers like or dislike about existing competitors' products. For example in Figure 29 the questionnaire is used to ask questions about the qualities of chilli sauce.

However, if producers wish to make products that are new to an area, they need to have samples for potential consumers to taste and give their opinion on whether they like the product and would be willing to buy it. (When asking people to taste a product, a supply of spoons should be taken so that each person interviewed uses a clean one). Samples can usually be made at home using domestic equipment so that an investment in production facilities is not needed at the this stage. An example of a questionnaire for a new product is shown in Figure 30.

Although initially, new products have the advantage that there will be no competitors, the process of assessing demand takes longer and costs more than for products that are already known. In addition, as up to 80% of new products fail, the risks are higher and it may be more difficult to get a loan for this type of work.

Figure 29. - Example of a survey questionnaire on the quality of competitors' chilli sauce

Questions

1

2

3

4

5

Very good

Good

Average

Bad

Very bad

1.

Which make(s) of sauce do you by most often?

Write names of sauce(s)

1.

What do you think about the colour of the sauce you buy?

Tick in the appropriate place

2.

What do you think about the seeds being present in the sauce?

3.

Do you like the thickness of the sauce?

4.

What do you think about the flavour of the sauce?

5.

Do you like the bottle?

6.

What do you think about the label?

7.

What do you think about the price of the sauce?

8.

Is there anything else that you think is good about the sauce that you buy at present?

Write answers

9.

Is there anything else about the sauce that you buy that you would like to see improved?

Write answers

Remember that the customer (the person who buys the food) is not always the same person as the consumer (the one who eats the food). This is particularly important when getting information about the quality of foods that are mostly eaten by children, as their preferences for colour or sweetness may be different to those of their parents (see also Section 2.8.1). For food producers, customers can also be retailers or other sellers in addition to institutions, other food processors and members of the public.

The results of such surveys can be analysed by adding together the numbers of people that gave answers such as 'very good', 'poor' etc. In the example below, the answers to questions about chilli sauce (Table 12) show that among other information, 88% of people found the colour of the sauce to be better than average, 78% did not like having seeds in the sauce and 60% found the flavour to be good or very good.

Other information that can be gained by analysing the data includes:

1. a large majority of consumers liked having sauce in a bottle and that they were happy with existing labels. This information helps to show a new producer what type of packaging must be used if he/she is to compete effectively with existing manufacturers or imported foods.

2. A majority of consumers (52%) were unhappy with the price of the sauce and this indicates that a potential market share exists, if a new product having a similar quality can be sold more cheaply.

Figure 30. - Sample questionnaire for a new product (tomato jam)

Explain to each person you interview that you wish to start a new business making tomato jam and that you have prepared some samples for people to try. Ask them if they would like to taste the sample and give you their opinion on what it is like.

Question

Answers

1. Do you eat other types of Jam?

Yes/No...................... Circule answer

2. Which types of jam do you like best?

List the types

3. Do you think you would like tomato jam?

Yes/No/Not sure...... Circule answer



1

2

3

4

5

Very good

Good

Average

Bad

Very bad

4. What do you think about the colour of this tomato jam?

Tick in the appropriate place

5. Do you like having the seeds in the jam?

6. What do you think about the flavour of this jam?

7. Do you like the texture of the jam?

8 What do you think about the jar?

9. What do you think about the label?

10. What else do you like about this jam?

Write answers

11. Is there anything that I can do to improve this jam?

Write answers

Survey of market size and value

A different set of questions are needed when assessing the size of the market for a particular type of food (the total weight of product that is bought per month or per year) and the value of the market (the amount of money spent on that product each month or year). At the same time it is possible to gather information about the types of people who buy a particular food and where they buy it. A sample questionnaire is shown in Figure 31.

The information gathered from potential consumers, using questionnaires like the ones in Figures 29 to 31, can be analysed by the entrepreneur to get a good idea of the quality characteristics of the product that consumers prefer, the total demand for the product and the total value of the market. However, this involves making a number of assumptions and it is important to consider the following:

1) are the people interviewed really representative of all potential consumers?
2) were enough people interviewed?
3) were people giving accurate information?

Table 12. - Data collected about consumers' opinions of the quality of a product

Question

Summary of 50 replies

1

2

3

4

5

Total

Very good

Good

Average

Bad

Very bad


1. What do you think about the colour of the sauce you buy?

12

32

5

1

0

50

2. What do you think about the seeds being present in the sauce?

5

6

16

14

9

50

3. Do you like the thickness of the sauce?

10

20

12

7

1

50

4. What do you think about the flavour of the sauce?

42

8

0

0

0

50

5. Do you like the bottle?

40

10

0

0

0

50

6. What do you think about the label?

10

11

20

9

0

50

7. What do you think about the price of the sauce?

5

7

12

25

1

50

If a producer is unsure about the quality of information that has been given, he or she should ask more people the same questions to check the answers obtained. Clearly, the more people that are interviewed, the more accurately does the information reflect the real situation. However, a balance has to be drawn between the time and cost of interviewing large numbers of people and the accuracy of the data that is obtained. As a guide, 50-75 interviews should result in a good idea about the market for a product in a particular area.

When analysing data collected about market size and value, it is often helpful to find official statistics about the people who are expected to be the customers for a new product. For example in Table 13, information was collected using a market survey of chutney consumption in a small Asian town and analysed together with data from the Census Office and a previous socio-economic survey about the size and wealth of the town's population. Similar information is sometimes available from Local Government offices, tax authorities and Chambers of Commerce, although it may not always be up to date.

Figure 31.- Sample questionnaire about market size and value

Questions

Answers

About the market size:

1. How often do you buy this product?

Daily/weekly/monthly

2. Do you buy different amounts at different times of the year?

(Circle answer)
Yes/No (Circle answer)

3. When are the times that you buy the most?

Write answer

4. How much do you buy each time?

Write amount in kg or No. Packs

5. When are the times you buy the least?

Write answer

6. How much do you buy each time?

Write amount in kg or No. Packs

7. What is the amount of food in the pack?

Write amount in kg

About the market value:

8. How much do you pay for a pack of the food?

Write the amount in currency

9. What is the price difference for larger or smaller packs?

Write differences

10. Does the price change at different times of the year?

Yes/No (Circle answer)

11. When is the price highest?

Write answer

12. When is the price lowest?

Write answer

About the customer:

13. Would you say that you have a low, medium or high income in your household?

Low/medium/high (Circle answer)

14. In which age group do you belong?

Tick answer


1-20



21-40



41-60



Male/Female

M/F (Circle answer)

About sales outlets:

15. Where do you usually buy this food:

Tick answer


Market stall



Local shop



Kiosk



Supermarket



Street hawker



Directly from producer



Other

Write answer

Table 13. - Potential market for chutney in a small Asian town

Type of customer

Number in each category*

Amount of chutney bought per month (kg**)

Amount of chutney bought each time (kg**)

Low income

18,430

0.4

0.1

Medium income

5,485

1.2

0.15

High income

192

2.25

0.45

* from official census statistics for the town
** average of information given by 70 customers interviewed

The cost of chutney in the market was $3.9 per kg when sold in 100g amounts from a bulk container into customers' own pots (bought by the majority of those who said they were in low income families), $4.1 per kg when sold in 150g plastic bags (bought mostly by medium income families) and $4.8 per kg when sold in 450g glass jars (bought mostly by high income families). This data can be analysed, as shown in Tables 14 (a) and (b), to calculate the total size and value of the chutney market in this town.

The size and value of the market, calculated in Table 14, indicate that low income and medium income families form the largest part of the chutney market in this town. These people were found to buy the product either from bulk containers into their own pots, or pre-packed in plastic bags. The demand for jars of chutney was limited to high income groups which formed only 3% of the market size and 3.8% of its value. A new business would therefore be likely to focus on low and medium income families as its potential consumers. This has implications for not only the type of packaging that is used but also the types of advertising, methods of promotion and agreements with retailers that should be considered. These aspects are described in more detail in Section 2.8.

Table 14 (a). - Calculation of the size of the market for chutney

Type of customer

Number in each category

Amount of chutney bought per month (kg)

Total demand (kg per month)

Low income

18,430

0.4

7,372

Medium income

5,485

1.2

6,582

High income

192

2.25

432

TOTAL


14,386 kg

Table 14 (b). - Calculation of the value of the chutney market

Type of customer

Amount of chutney bought each time (kg)

Cost per kg of chutney ($)

Number of kg

Value of market ($ per month)

Low income

0.1

3.9

7,372

28,751

Medium income

0.15

4.1

6,582

26,986

High income

0.45

4.8

432

7,882

TOTAL


$63,619

Market share and competition

Market surveys and the calculation of market size and value are important to find out whether the demand for a product really exists, but these figures should not be assumed to represent the scale of production that could be expected. Even if no-one else is currently making a product locally, it is likely that once a new business starts production and is seen by others to be successful, they too will start up in competition. It is therefore important from the outset, to estimate what is the proportion of the total market that a new business could reasonably expect to have. This is known as the market share. It is often difficult to estimate a realistic market share and the figure depends on a large number of variables, but Table 15 can be used as an initial guide. In many cases, new entrepreneurs over-estimate the share that they could expect, with the result that production operates at only a small proportion of the planned capacity. The lower percentages in Table 15 should therefore be used initially. Section 2.3.4 describes some of the negative effects on finances of operating a business below planned capacity.

In the example described in Tables 13 and 14 concerning the market for chutney, there were a large number of small producers all making similar products. The estimated share of the market for a new producer can therefore be calculated as follows:

Total size of the market = 14,386 kg per month

Estimated share = 5-10%, with 5% selected.

This represents sales of 719 kg of chutney per month with a potential value of $3,181 per month.

When converted to daily production rates, assuming 20 working days per month, the maximum production is therefore 36 kg per day

This figure for daily production rate is very important. It is central to all subsequent calculations of production capacity and investment requirements (below) and every care should be taken to ensure that this information is as accurate as possible.

It should be noted that in the calculations below, the scale of production is based on an anticipated share of the total market. In other situations, a more detailed analysis of market segments could be made (Section 2.8.1) and the planned market share could be based on one of those segments (e.g. low income groups in Tables 13 and 14).

Competitors are very important to the success or failure of a new business and the entrepreneur should recognise that there are different types of competitor. Using the example of someone wishing to make fruit juices, it is helpful to think how the consumers might view the available products: for example when they are thirsty, they have a choice of hot drinks (tea, coffee etc.), cold soft drinks, such as milk, juices, squashes or finally alcoholic drinks. These are all general competitors, who are able to satisfy the consumers' thirst. Supposing the consumers choose cold soft drinks that can be drunk straight from the bottle, they then have a choice between carbonated (fizzy) soft drinks, and juices. These are known as type competitors or different kinds of soft drink. Finally, on choosing juices, there are different juices and different brands of the same type of juice, which are brand competitors.

Although the appearance and quality of foods are important, competitors do not just compete with their products. They also compete with the profit margin and level of service that they offer to retailers and with special offers or incentives to customers. New entrepreneurs must therefore assess each of these factors when deciding what the competition is and how to deal with it. This is conveniently done using a SWOT analysis, where SWOT stands for Strengths, Weaknesses, Opportunities and Threats.

The technique involves looking at each aspect of the new business and comparing it to other producers, particularly type and brand competitors.

Many new entrepreneurs do not appreciate the importance of finding information about competitors and even if they do, they may not know where to find it. In addition to the direct questions to consumers in market surveys described above, entrepreneurs can get information about competitors from the following sources:

1. discuss with retailers the amount of sales of different brands and any seasonality in demand. What are the trends in consumers' buying, what is getting popular and what is going down? What types of consumers buy particular products and how often? Does the retailer put on any special displays for some suppliers? What do they think about the idea for a new product and do they think they will sell a lot of it? What are their plans for the future?

2. look at competitors' advertising and retail displays, get a copy of their price lists.

3. ask the local Employer's Federation or Chamber of Commerce for any information

they have on the market for similar products.

4. visit trade fairs and talk to other producers and their customers.

5. look in trade journals, manufacturers' association magazines and newspapers for information about the market and the activities of competitors.

Table 15. - Estimates of market share for a new food business with different levels of competition

No. of other producers

Many

Few

One

None



Size of competitors

Large

Small

Large

Small

Large

Small

Product range

S

D

S

D

S

D

S

D

S

D

S

D

Market share (%)

0-2.5

0-5

5-10

10-15

0-2.5

5-10

10-15

20-30

0-5

10-15

30-50

40-80

100

S = similar products, D = dissimilar products

(From Do Your Own Scheme, Anon)

After finding as much information as possible, the entrepreneur can then start to compare the new business with those of competitors using the SWOT analysis. An example of how it might appear is shown in Table 16.

When it is completed, the entrepreneur should be able to answer the following questions:

· who is producing similar products?
· where are the competitors located?
· what is the quality and price of their products?
· what can I do to make a new product that is better than those of competitors?
· why would customers or consumers want to change to a new product?
· what offers or incentives do competitors give to retailers?
· what are competitors likely to do if a new product is introduced?

The answers to these questions are then used to formulate a marketing strategy, details of which are described in Section 2.8.2.

The analysis in Table 16 indicates that one competitor (A) has a range of good quality products that are packaged and promoted well, but they are more expensive and do not meet changing consumer requirements. The other competitor has a cheap product that is not well packaged and not promoted. However, it sells well because the low price attracts low income consumers and retailers promote it because of the higher margins offered by the company. They appear to be expanding to new areas. However, retailers are annoyed when Competitor B fails to deliver on time or in the correct amount and they may have over-stretched their distribution capacity. The analysis points the way to producing a product without additives and to providing a good service and equivalent margins for retailers. It also highlights lack of information about process inputs (e.g. packaging) and production costs. These are discussed in the Sections below.

2.3.3. Technical feasibility


Production planning
Weights of raw materials and ingredients
Equipment required
Packaging
Staffing levels


Once an entrepreneur has found information about potential consumers, their requirements and the likely share of the market that could be obtained for a new product, it is then necessary to assess whether production at this scale is technically feasible. The series of questions below is helpful in deciding the technical requirements of the business:

· are enough raw materials available of the correct quality when needed for year-round production?

· is the cost of the raw materials satisfactory?

· is the correct size and type of equipment available for the expected production level and at a reasonable cost?

· can it be made by local workshops and are maintenance and repair costs affordable?

· is sufficient information and expertise available to ensure that the food is consistently made at the required quality?

· are suitable packaging materials available and affordable?

· are distribution procedures to retailers or other sellers established?

· is a suitable building available and what modifications are needed?

· are services (fuel, water, electricity etc.) available and affordable?

· are trained workers available and are their salaries affordable?

Table 16. - Example of a SWOT analysis of a new business in relation to competitors


My proposed business

Competitor A

Competitor B

Strengths

Production likely to be sited close to retailers can deliver at short notice.

Good brand image and range of products.

Product is cheaper than A and sells well They offer good margin to retailers.

Weaknesses

Difficult to find good packaging.

Products more expensive than B. Uses synthetic colours and preservatives.

Poor quality product, poor label design. I'm told by retailers that supplies are irregular and not always the amount ordered.

Opportunities

Retailers say demand for products without additives is increasing. I can produce without added colours.


Appears to be expanding deliveries to new areas according to newspaper reports.

Threats

Strong promotion by A. There are few wealthy consumers and price is most important factor. I am not yet sure of production costs.

Cheaper products than B.

May have over-expanded distribution network and failing to make deliveries.

(Adapted from: Starting a Small Food Processing Enterprise, by Fellows, Franco and Rios)

Production planning

The answers to these questions can be found by first setting down a plan of the production process in a similar way to the process charts described in Section 2.2. This plan should indicate how the different stages in a process are linked together, identify any 'bottle-necks' in the process, the equipment that is required for each stage and where quality assurance procedures should be used. The data that has been found from market surveys is added to the process chart to indicate the scale of production that is required (e.g. Figure 32, which uses chutney as an example).

The chart is also used for planning a number of different aspects of the production process, including:

1) the weights of raw materials and ingredients that should be scheduled each day,
2) the number of workers and their different jobs,
3) the size of equipment required to achieve the planned throughput of product
4) the number of packages that are required each day.

In the example, the market information for chutney sales indicated that a minimum production rate of 36 kg per day would be needed to meet the anticipated initial market share. Assuming that production takes place for 8 hours each day for 20 days per month, the average throughput would be 4.5 kg per hour (36/8 kg). This throughput figure is critically important in all subsequent planning and every effort should be made to ensure that it is as accurate as possible by checking all assumptions carefully. In particular, the number of assumed working days may fall below twenty if there are regular power failures or if production planning (Section 2.7.1) is inadequate. The different stages of production planning are described below.

Figure 32. - Modified process chart showing scale of operation and daily requirements for mango chutney production

Processing stage

% losses

Weight of mangoes (kg)

Batch size (kg)

Processing time (minutes) from Figure 33.

No. of workers

Minimum equipment size (kg/hr)

Mangoes

0

60





Wash

14

60





Sort

45

51.6


90

2

Table for 2 workers

Peel/destone

0

28.4





Cut


28.4


120

3

Table for 3 workers, 3 knives

Mix

0

27

27 kg sugar + 13.51 vinegar for batch of 60.7 kg.




Boil

34*


40

180

1

Boiling pan for 10 kg batches. Two filters and heat sealers. Table for 2 people

Fill/seal

10


36

180

2

Cool/label

0


36

120

1

Store

0


36



Weight of product



36



* evaporation losses during boiling. Note: recipe described in Figure 13.

Notes on calculations:

Boiling results in weight losses of 34% as water is evaporated and the solids content increases to 70% (see calculation below). If each batch takes 20 minutes to boil, there are 2 batches per hour and in 3 hours there are 6 batches of 10 kg each to meet production target of 60 kg of raw materials, yielding 36 kg of product per day. Therefore the boiling pan should have 10 kg working capacity (that is a 12-15 litre pan).

Each worker fills and seals 40 bags per hour = 120 bags per day x 2 workers = 240 bags of 150g net weight = 36 kg per day

Calculation of boiling losses:

The solids content in the mix of ingredients before boiling is found as follows:

Ingredient

Weight (kg)

Solids content (%)

Weight of solids (kg)

Mangoes

27

15

4.05

Sugar

27

100

27

Vinegar

13.5

0

0

Total

67.5


31.05

Total weight after 10% losses

60.7 kg


28

% solids in batch before boiling = (28/60.7) x 100 = 46%

So 28 kg equals 46% of the batch before boiling. After boiling there is no loss of solids (only water is removed) but the solids content has been increased to 70%.

Therefore 70% still equals 28 kg.

Therefore the total weight of the batch after boiling = (100/70) x 28 = 40 kg

Weights of raw materials and ingredients

There are two stages involved in planning the amounts of materials that are needed to produce the required weight of product: first, it is necessary to calculate the amount of each ingredient that will be needed to formulate a batch of product and secondly, it is necessary to calculate the amount of losses that can be expected during preparation of fruits and vegetables.

The processor should experiment with different mixes of ingredients (the 'formulation' or 'recipe') to produce a product that has the colour, flavour, appearance etc. that consumers say they prefer from market research. Skill and flair are needed to achieve this, using the combination of ingredients that has the lowest cost. It is important to weigh each ingredient carefully and make sure that all weights are recorded for each formulation that is tried.

Otherwise, the inevitable result is a successful trial product, but no information is recorded to enable it to be repeated. Once a formulation has been successfully developed, great care is needed to ensure that it is made in exactly the same way on every occasion. This requires staff training, especially for those staff involved in batch preparation, the implementation of quality assurance procedures and careful production control. These aspects are discussed in more detail in Sections 2.7.1 and 2.7.2.

Nearly all fruit or vegetable processing results in losses of material. These may arise from peeling or de-stoning, from unsatisfactory fruits and vegetables that are thrown away during sorting, from spillage during filling into packs or from food that sticks to equipment and is lost during washing. Different types of fruit and vegetables have been found in practice to have different levels of wastage and examples of some of these are given in Table 17. Typical losses from other sources in a well-managed production process are shown in Table 18. However, it is necessary for an entrepreneur to do trials to calculate the actual amount of wastage experienced with the particular varieties of fruit or vegetable and with the particular process that are being used.

Clearly, it is in the interests of the processor to reduce losses as much as possible. Contracts with reliable suppliers (Section 2.6.1) help to ensure lower levels of poor quality raw materials and therefore reduce losses. Additionally, a well-managed processing operation, having good quality assurance procedures (Section 2.7.2), also reduces wastage, especially during later stages of a process when the product has a higher added value.

Using the data from experimental production trials, or less desirably estimates based on data in Tables 17 and 18, it is necessary to calculate the amount of raw materials and ingredients that are needed to produce the required weight of product each day. This will also enable the true cost of raw materials to be calculated for use in financial planning (Section 2.3.4)

Using mango chutney as an example. Figure 32 shows losses during each stage of the process. The amount of mangoes that need to be bought to produce the required weight for each day's production can then be calculated. The result indicates that only 45% of incoming raw materials were actually used in the product (27 kg of the 60 kg bought). If mangoes were bought for $0.2 per kg in season, the true cost of the fruit is calculated as $0.44 using the following formula:

Other ingredient costs are estimated as follows: sugar $0.6/kg, vinegar $1.25 per litre and total spice costs of $1.3 per day. This data is used to calculate operating costs in Section 2.3.4.

Table 17. - Typical losses during the preparation of selected fruits and vegetables

Fruit or vegetable

Typical losses during preparation (%)

Notes

Apples

23

peeled & cored

Apricot halves

12

destoned

Bananas

41

peeled

Cabbages

30


Carrots

4

(bought without leaves)

Cauliflowers

38


Currants

3

seeds & skins removed

Figs

2


Grapes

19

skins & pips removed

Guava

22


Lemons

40

peel & seeds removed

Mangoes

45

peeled & destoned

Melons

42

peel & seeds removed

Okra

12


Onions

3


Oranges

25

peel & seeds removed

Passion fruits

58

peel & seeds removed

Pawpaws

38

peel & seeds removed

Peas

50

bought in pods

Peppers - chilli

15

seeds & stalk removed

Peppers - green

14

seeds & stalk removed

Pineapples

48

peeled & cored

Plantains

39

peeled

Tomatoes

4

seeds & skin removed

(Adapted from data in The Composition of Foods by Paul and Southgate, and from field data collected by the author)

Equipment required

Using the process chart (Figure 32), the weight of food that should be processed at each stage is then calculated in kg per hour. This information then allows the processor to decide what equipment is required and the size (or 'scale' or 'throughput') that is needed. In doing this, decisions need to be taken on the relative benefits of employing a larger number of workers or buying machinery to do a particular job. In some enterprise development programmes, there may be wider social objectives of employment creation which may influence such decisions.

The decisions on equipment requirements are also influenced by:

· the cost and availability of machinery
· the availability of people who are skilled in
· maintenance and repair
· the availability and cost of spare parts and
· the possibilities of local equipment fabrication.

Information on the types and suppliers of equipment is often difficult to obtain, but catalogues and sometimes databases of equipment manufacturers and importers may be available at offices of national and international development agencies, Chambers of Commerce, university departments, food research institutes, embassies of other countries and trade or manufacturing associations.

Table 18. - Typical Losses During Processing of Fruits and Vegetables.

Stages in a Process

Typical losses

Washing fruits/vegetables

0-10

Sorting

5-50*

Peeling

5-60

Slicing/dicing

5-10

Batch preparation/weighing

2-5

Boiling**

5-10

Drying**

10-20

Packaging

5-10

Machine washing

5-20

Accidental spillage

5-10

Rejected packs

2-5

* Unsatisfactory raw materials depend on source and agreements with suppliers
** does not include evaporation losses

It is preferable wherever possible, to buy equipment from local suppliers and fabricators because servicing and obtaining spare parts should be faster and easier. However, if equipment has to be imported, the following points should be considered: when ordering equipment, it is important to specify exactly what is required, as many manufacturers have a range of similar products. As a minimum, it is necessary to state the throughput required in kg per hour and the type of food to be processed. Where possible other information such as the model number of a machine, whether single or three-phase power is available and the number and types of spares required, should also be given. Assistance from a food technologist working in a local university or food research institute may be required to research and order equipment. The quotations received from equipment suppliers can then be used when calculating financial viability (below).

Packaging

Similar considerations apply when ordering packaging materials as there is a very wide range available and there are a number of considerations that should be taken into account by the producer. These include the technical requirements of the product for protection against light, crushing, air, moisture etc. (described in Section 2.5.5. and for individual products in Section 2.2), the promotional and marketing requirements (Section 2.8.3) and the relative cost and availability of different types of packaging. Selection of packaging materials frequently causes the largest problems for small producers and is often the main cause of delay in getting a business established. Professional advice should be sought from a food technologist or in some countries, packaging specialists or agents of packaging manufacturers.

Staffing levels

Decisions on the numbers and types of workers that are required to operate the proposed business are taken in conjunction with decisions on equipment procurement. Using the process chart, it is possible to break down the production into different stages and then decide the number of people who will be needed for each stage of the process. It is important also to include work such as store management, quality assurance and book-keeping when planning employment levels.

In fruit and vegetable processing, each day's work will initially involve preparation of the raw materials and then move through processing to packaging. It is possible to have all workers doing the same type of activity throughout the day, but it is often more efficient to allocate different jobs to each worker as the day progresses. A convenient way of planning this is to draw an Activity Chart. This shows the type of work that is to be done each hour during the day, the number of people involved with each activity and the sequence of work that individuals will do during the day.

In the example of chutney processing, the total number of workers is estimated from the process requirements shown on the process chart (Figure 32). It is estimated that two workers will be able to wash and sort 40 kg mangoes within ninety minutes. Similarly, it will require three workers to peel and slice this amount of fruit within two hours (Figure 33). Once sliced fruit becomes available (by around 9.30 am), one of the three workers (X) can begin preparing the batches of ingredients and boiling the chutney. By 11.00 am, fruit preparation has finished and while one worker (Y) washes down the preparation area, the third (Z) labels the previous day's production and packs them into boxes ready for distribution.

In this plan, all workers have a lunch break at the same time, but in other types of process it may be more convenient or efficient to stagger each person's break at different times. As the first batch of product cools sufficiently, work can begin after lunch on filling and sealing it into 150g plastic bags. This is a time-consuming stage as manual filling and sealing have been selected. Additionally, packages require check-weighing to ensure that they contain the correct weight of product (Sections 2.4.2 and 2.7.2). It is calculated that three hours will be needed for two people to fill and seal 240 bags (36 kg). This time could be reduced if a mechanical filler/sealer was bought, particularly at a later time when the business expanded. In the example, the owner/manager (M) is involved with staff supervision, record keeping, finance management and product distribution/sales. In other plans, these jobs could be done by trained staff.

Figure 33. - Activity chart used to plan job allocations for staff to produce mango chutney

This type of chart is useful for assessing the time required to complete each stage of the process and for thinking through the problems that are likely to occur. When production begins, it can be used as a basis for training in each job and it should be constantly reviewed to optimise production efficiency.

In summary, the technical part of a feasibility study involves taking information about the expected demand from the market survey and calculating the process throughput required to meet that demand. This can then be used to decide on the type of equipment, the level of staffing and the amounts of raw materials, ingredients and packaging that will be required. These are summarised, using the example of chutney production, in Table 19.

Table 19. - Summary of technical feasibility calculations for mango chutney production

Information required

Data obtained

Estimated market size (kg/month)

14,386

Estimated share of market

5

Production required per month to meet market share (kg)

719

Production required per day @ 20 days' work per month (kg)

36

Minimum Process throughput @ 8 hours per day (kg/hr)

4.5

Weight of mangoes required per day (kg)

60

Losses on arrival due to sorting (%)

14

Amount of losses in the process (%)


- wastage/spillage

10


- peeling losses

45


- mixing losses

15


- packing losses

10


- evaporation losses during boiling (%)

34

Minimum size of equipment required (kg/hr) for


washing/sorting

60


peeling/slicing

40


boiling (2 batches of 10 kg per hour)

10


packing (bags per person per hour)

40

Number of people required to operate the process

3 plus owner/manager

2.3.4. Financial feasibility


Start-up costs
Operating costs
Income and profit
Financial planning
Preparing a business plan


Having completed the study of technical feasibility, the entrepreneur should then have sufficient information to determine the costs that are likely to be involved in production. Additionally, the market survey will have supplied information about the sale price that could be achieved for the new product. The entrepreneur is therefore in a position to calculate the expected income and expenditure and hence the gross profit that can be achieved.

Start-up costs

When a new fruit and vegetable processing business is started, it is likely that money will be required to buy or convert a building and buy equipment to start production. Details of suitable buildings are given in Section 2.5.3. Additionally, it is necessary to buy a stock of packaging materials and the initial raw materials and ingredients. The start-up capital is the amount of money that is needed to buy the facilities and equipment, to register and licence the business and get the necessary hygiene certificates.

Working Capital includes the costs of raw materials, packaging, staff training, product promotion etc. that have to be made before the business begins to generate income from sales of the product. The requirement for working capital also continues as the business develops and is discussed further under 'Cashflow' below. As described in Section 2.7.1, fruit and vegetable processing has relatively high requirements for working capital compared to other types of food processing. This is because of the seasonal nature of crop production and the need to buy several month's supply of crops during the season and part process them so that production can continue for a larger part of the year.

The start-up capital and initial working capital are calculated to determine whether the entrepreneur's savings (known as the owner's equity) will be sufficient to start the business without a loan. Using the example of chutney production, the start-up costs are estimated in Table 20, using representative data from the country concerned.

Table 20. - Start-up costs for chutney production

Start-up cast

$

Conversion of building (Section 2.5.3)

800

Equipment (from Figure 32)

350

Registration of business

50

Business Licence

25

Hygiene inspection and certificate

50

Raw materials & ingredients for 4 weeks' production (from Figure 32)*

927.5

Packaging (minimum order)

200

Staff training (equivalent to income from 2 weeks' production value)**

1476

Initial production promotion

250

Staff salaries for 6 weeks

360

TOTAL

4488.5

* 60 kg mangoes/day @ $0.2/kg = $240/month,
27 kg sugar/day @ $0.6/kg = $324/month,
13.5 litres vinegar/day @ $2.25/litre = $337.5/month,
Spices cost $1.3/day = $26/month
** Sales @ $4.1/kg (Table 14) x 36 kg/day = $1476 for 2 weeks.

The owner's equity is $2,500 and a loan of $1,989 is taken to meet the total start-up costs. (A further option of a second partner's equity of $2,000 is agreed at the same time to take account of a negative cashflow during the first year of operation (see Table 22)).

Operating costs

There are two types of operating (or production) costs: those expenses that have to be paid even if no production takes place and those that depend on the amount of food that is produced. The first type are known as fixed costs and the second type are variable costs. Examples of each are shown in Table 21 again using chutney production as an example.

Table 21. - Summary of fixed and variable operating costs for mango chutney

Type of Production Costs

Actual costs for Chutney Production per Year ($)

FIXED COSTS


Rent

1200


Labour*

2880


Loan repayment**

19898


Interest charges**

796


Professional fees (e.g. accountant's fees)

120


Maintenance of equipment (10% of value)

35


Depreciation of equipment (over 3 years)

117


Business registration fees, hygiene certificates and other licences

125


Total fixed costs

7262

VARIABLE COSTS


Raw materials (Table 20)

2880


Other ingredients

8250


Fuel

800


Power

250


Packaging materials

1800


Transport/distribution

450


Labour*

-


Advertising and promotion

1150


Total variable costs

15,580

Total operating costs per Year

22,842

* Labour is a fix cost if workers are permanently employed as full-time staff, but it is described as a variable cost if people are only employed when production takes place. In this example, permanent labourers are paid $80/month.

** In this example, the loan of $1989 is repaid within the first year with a fixed interest rate of 40% per month.

Income and profit

From the market survey, the estimated market size and share enables the expected sales to be calculated. The gross profit (or gross loss) is the difference between the expected income and the total operating costs over the first year, including any loan repayments. Income is therefore calculated as follows:

Income = Selling price per unit x number of units sold

The income clearly depends on both the price of a product and the amount that is sold. When selecting a price for a product, two approaches can be taken: first the price can be based on production costs and it is set to ensure that income exceeds the total costs. This however, does not take account of competitors' prices and to be successful, the new product should be priced at or below the price of other similar products.

The second approach is therefore to set the price to compare favourably with existing products and calculate the likely profit at the planned scale of production.

Unless the new product is to be sold directly from the production unit or through a sales outlet owned by the producer, it is also important to remember the profit that will be expected by retailers. In many countries this profit is normally 10-25% of the value of each pack. In addition, there are distribution costs and perhaps special promotion costs that should also be included. The price that is charged for the product should therefore allow the producer, the distributors and the retailers to make an adequate profit. In the example using mango chutney, the income to the producer is the sale price less 10% for retailer's profits ($4.1 - 10% = $3.7/kg).

When the production costs and income are compared using the second approach, the operation of the business should be above the breakeven Point. Above this point is the minimum level of production that can enable the enterprise to make a profit (Figure 34).

Figure 34. - Breakeven Point

Breakeven point can be calculated as follows:

· calculate the contribution for variable costs per pack

· subtract the value obtained from the sale price to obtain the 'unit contribution'

· calculate the total fixed costs per year

· divide the fixed costs by the unit contribution to obtain the annual production rate that will allow the business to break even

In the example of chutney production, the contribution for variable costs per pack (Table 21) = $ 15,380/57,600 bags per year = $ 0.270

The sale price per pack = $ 3.7/kg/6.61 packs per kg = $ 0.555 per pack

Unit contribution = sale price - (variable + labour contributions) = 0.555-0.270 = 0.285

Total fixed costs per year = $ 7262

Breakeven = fixed costs/unit contribution = 7262/0.285 = 25,481 packs per year

When expressed as a % of total production capacity (57,600 bags per year), the breakeven point = (25,48157,600) x 100 = 44.2%

In other words, the processor must operate at above 44% of the available capacity in order to make a profit. Clearly the higher the figure for the break-even point, the more difficult it is for a process to be profitable.

The annual production costs are calculated in Table 21 as $22,842. If all products are sold, the annual income is calculated to be $31,968 (36 kg per day @ $3.7/kg x 240 days per year). This leaves a gross profit of $9,126 per year, which after taxes, is available to pay the owner a salary and for re-investment and expansion of the business.

If the feasibility study shows that the scale of production required to meet the expected market share is below the break-even point, the entrepreneur should carefully examine the data to see if production costs can be reduced. If not, there is a question over the wisdom of proceeding further with the proposed business.

It should be noted that entrepreneurs should not automatically consider the gross profit as their own income. The money belongs to the business and they should take a fixed wage, which is recorded as another business expense. A common source of business failure happens when an owner removes cash to pay for a funeral or other family occasions and disrupts the cashflow of the business to a point that it cannot continue trading.

Financial planning

If the gross profit indicates that the proposed fruit and vegetable processing business is likely to be successful, it is then necessary to repeat the calculation of monthly gross profit for one to three years. This will then show whether there is sufficient cash available to operate the business without the need for further loans. This is known as a cashflow forecast and an example, calculated for one year only for chutney manufacture, is given in Table 22.

Table 22. - Example of cashflow forecast for chutney manufacture

Month

J

F

M

A

M

J

J

A

S

O

N

D

Total

Income ($'000)

0.4

0.6

1.0

1.2

1.2 + 2.0

1.9

2.1

2.2

2.5

2.7

2.7

2.7

22.2

Expenses ($'000)

1.0

1.2

1.4

1.5

1.7

1.8

1.8

1.8

1.8

1.8

1.8

1.8

19.4

Cumulative Profit/loss ($'000)

(0.6)

(1.2)

(1.6)

(1.9)

(0.4)

(0.3)

0

0.4

1.1

2.0

2.9

3.9

2.8

Figures in ( ) indicate a negative cashflow. The second partner's equity of $2000 was taken in May.

From the data in Table 22 it can be seen that during the initial start-up period during January and February, production routines were becoming established and as a result, sales were low. The expenditure on supplies of packaging materials and fruit during this time leads to an accumulated negative cashflow of $1,900 by April. This illustrates one of the benefits of conducting a feasibility study: the losses made over the first few months are planned and can be addressed by taking out a loan or using the owner's equity. This gives both the owner and any lenders the confidence to know that the business is under control and that the negative cashflow will cease, in this case after seven months. Lenders are more willing to provide a loan if they are confident that the finances of the business are planned and managed. This should not be done just at the start of a business but also later on, if sales are expected to fall for a while or if raw material costs rise temporarily (e.g. when the harvest season finishes). A particular problem for all small businesses is the need to order packaging materials in bulk because of minimum order sizes. This expenditure and the need to tie up cash in stored packaging can be very damaging to a business cashflow. The entrepreneur should assess the alternatives of paying a higher unit price for small amounts of packaging or suffering a negative cashflow.

A similar forecast is made to show the expected development of the business over three years (not forgetting to take account of the expected actions of competitors). Finally, in assessing financial feasibility, the data is presented as a Profit and Loss Statement, to calculate the net monthly profit before tax over the first three years. An example of a monthly profit and loss account is shown in Figure 54.

Preparing a business plan

The advantages of writing down the results of the feasibility study are as follows:

· the findings can be set out in a clear and logical way, so that potential lenders can understand the business and its likely risks/advantages

· the document helps the entrepreneur to clarify and focus his/her ideas

· it is reference material that can be used to plan long term development of the business

· the plan can be regularly consulted and updated as a guide to the business development

· mistakes can be made on paper rather than in the operation of the business

· when the plan shows that a successful business is possible, it makes the entrepreneur feel more confident about success

· it helps the entrepreneur to decide how much money is needed and if properly prepared, it gives the loan agency confidence that their money will be repaid.

Most lenders have little understanding of fruit and vegetable processing and the entrepreneur should therefore write the business plan in a simple way, avoiding jargon and technical language as much as possible. If lenders can understand what is involved in the business, they are more likely to approve a loan.

It is important to include as much detail as possible and if necessary do thorough research first. It is also important to look outwards from the business to judge what competitors will do and how the business will develop to become sustainable.

Although there is no fixed way of writing a plan, the sections that could be included are summarised as follows and in Appendix III:

Introduction: to summarise what the product is, who is expected to buy it, why the business is a good idea,

Basic information: the name and address of the owners, their qualifications and experience,

The product: details of the raw materials, the production process, quality assurance, packaging etc. What is special about the product compared to those of competitors,

The market: the potential customers, where they are located, the size and value of the market, expected market share, likely expansion (or contraction) of the market, the number and types of competitors, their strengths and weaknesses and their expected reactions to a new product,

Selling plan: distribution and sales methods, planned promotion, product cost,

Premises/equipment: where the business will be located, building to be used and services that are needed, steps taken to meet health and hygiene laws, equipment and its cost,

Finance: amount required for start-up and initial operation, including profit and loss statement and cashflow forecast for three years, owner's resources that will be used, size of loan required and what it is for, security on the loan,

Business registration: steps that have been taken or are planned to register the business with tax authorities, local government and Department of Health (or equivalent) for hygiene inspection and certification,

Future plans: objectives of the business and expectations for the next 3-5 years.


Previous Page Top of Page Next Page